- 001_New Project for a Flying Aces Club Rubber Model
- 002_Two Side Assembly (Part 1)
- 003_Two Side Assembly (Part 2)
- 004_New Bulkhed Patterns
- 005_Revised Measurements for Bulkhead Patterns
- 006_Calculated Wing Area
- 007_Framing Up the Horizontal Tail
- 008_Construction of a New Horizontal Tail
- 009_Framing of the Horizontal and Vertical Tails
- 010_Wing Tip Fabrication
- 011_Framing the Right Wing Panel
- 012_Framing the Left Wing Panel
- 013_New Fuselage Bulkhead Patterns
- 014_Joining the two Wing Panels
- 015_Major Wing Structure Setback
- 016_Revised Wing Dihedral Joint
- 017_Checking the Wing's Dihedral Angle
- 018_Mating Wing with Fuselage
- 019_Bottom Bulkheads & Stringers (Part 1)
- 020_Bottom Bulkheads & Stringers (Part 2)
- 021_Wing-Fuselage Integration
- 022_Fuselage Top Bulkheads and Planking for Rear Cockpit Opening
- 023_Planking of the Forward Cockpit Opening
- 024_Stripping Stringers
- 025_Redesign and Fabrication of Fuselage Stab Mount
- 026_Rubber Motor Rear Peg
- 027_Applying Stringers
- 028_Interference Problem
- 029_Drilling Nose Block
- 030_Lining the Front Face of the Fuselage
- 031_Nose Block Fabrication (Part 1)
- 032_Nose Block Fabrication (Part 2)
- 033_Completing Fuselage Stringers4
- 034_Tail Wheel Assembly
- 035_Tail Wheel Assembly Installation
- 036_Revision to Top Side Stringer
- 037_Crash Protector
- 038_Crash Protector Revision
- 039_Plug-In Landing Gear Mount
- 040_Design of the Plug-In Landing Gear
- 041_Plug-In Landing Gear Trial Fit
- 042_Windshield Design (Part 1)
- 043_Windshield Design (Part 2)
- 044_Windshield Design (Part 3)
- 045_Windshield Design (Part 4)
- 046_Windshield Design (Part 5)
- 047_Landing Gear Magnetic Retention
- 048_Revised Landing Gear Wire
- 049_Completing the Landing Gear
- 050_Wing-Fuselage Fillets (Part 1)
- 051_Wing-Fuselage Interface
- 052_Wing Center Section
- 053_Wing Trailing Edge Fairing
- 054_Wing-Fuselage Fillets (Part 3)
- 055_Wing-Fuselage Fillets (Part 4)
- 056_Wing-Fuselage Fillets (Part 5)
- 057_Wing-Fuselage Fillets (Part 6)
- 058_Wing-Fuselage Fillets (Part 7)
- 059_Making the Engine Exhaust Stacks
- 060_Engine Exhaust Stack Alignment Dowel
- 061_Fuselage Blue Tissue Covering
- 062_Instrument Panels
- 063_Preparing Structure for Covering
- 064_Covering the Rudder with Japanese Tissue
- 065_Covering the Stab Rudder with Yellow Japanese Tissue
- 066_Covering the Wing with Yellow Japanese Tissue
- 067_Left Wing Panel Washout (Part 1)
- 068_Left Wing Panel Washout (Part 2)
- 069_Recovering the Left Wing Panel with Washout
- 070_Fuselage Stringer Problem
- 071_Resolution to Fuselage Stringer Problem (Part 1)
- 072_Resolution to Fuselage Stringer Problem (Part 2)
- 073_Covering the Fuselage
- 074_Fuselage Tissue Seam Problems
- 075_Help with Fuselage Tissue Seam Problems
- 076_Reworking the Wing
- 077_Recovering the Wing (Part 1)
- 078_Recovering the Wing (Part 2)
- 079_Covering the Fuselage
- 080_Scalloping Bulkheads before Recovering the Turtle Deck
- 081_Mating the Wing with the Fuselage
- 082_Mating the Wing with the Fuselage (Part 2)
- 083_Finish the Tissue Covering
- 084_Revised Scale Rudder Covering
- 085_Trial Fit of the Vertical Tail
- 086_Nose Block Tissue Covering
- 087_Landing Gear and Crash Protector
- 088_Painting the Windscreen Frames and Exhaust Stacks
- 089_Scale Nose Block Openings
- 090_Revision to Nose Block Key
- 091_Black Tissue Aileron and Elevator Trim
- 092_A Krylon Spray Disaster
- 093_Arrival of Decals
- 094_Stab Recover, Flat Black Paint, Exhaust Stacks, and Wing Walks
- 095_Windscreen Windows and Anti-Glare Paint
- 096_Installation of Crash Protector and Front Windscreen
- 097_Installation of Tail Assembly
- 098_Motor Peg and Prop Installation
- 099_Weight and Balance
- 100_Project Completion (Tuesday, 1-29-13)
- 100a_Project Completion (Tuesday, 1-29-2013)
- 101_More Scale Like Wheels
- 102_Rubber Motor and Stuffer Stick
- 103_Featured in the March issue of Flying Models
